(HO2S Heater Control Circuit Bank 2 Sensor 1)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit Low Bank 2 Sensor 1)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit High Bank 2 Sensor 1)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 1 Sensor 1)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 1 Sensor 2)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 1 Sensor 3)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit Bank 2 Sensor 2)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit Low Bank 2 Sensor 2)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit High Bank 2 Sensor 2)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module indicating a fault in the heater circuit of the pre-catalytic or upstream oxygen sensor.
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 2 Sensor 1)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 2 Sensor 2)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Resistance Bank 2 Sensor 3)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit Bank 2 Sensor 3)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit Low Bank 2 Sensor 3)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problem if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(HO2S Heater Control Circuit High Bank 2 Sensor 3)
...Read MoreThis indicates that a fault was detected by the vehicle’s control module in the heater circuit for the oxygen sensor
A decrease in fuel economy and reduced engine performance.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Air Assisted Injector Control Range/Performance)
...Read MoreThe Air Assist Injector systems job is to atomize the fuel better when the throttle closes and with cold starts of the engine.
Hard to start when engine is cold, misfiring and engine stalling
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Air Assisted Injector Control Circuit Low)
...Read MoreThe Air Assist Injector systems job is to atomize the fuel better when the throttle closes and with cold starts of the engine.
Hard to start when engine is cold, misfiring and engine stalling
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Air Assisted Injector Control Circuit High)
...Read MoreThe Air Assist Injector systems job is to atomize the fuel better when the throttle closes and with cold starts of the engine.
Hard to start when engine is cold, misfiring and engine stalling
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(MAP/MAF Throttle Position Correlation)
...Read MoreThe Air Assist Injector systems job is to atomize the fuel better when the throttle closes and with cold starts of the engine.
Hard to start when engine is cold, misfiring and engine stalling
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(MAP/MAF Throttle Position Correlation)
...Read MoreA fault exists when the difference between the manifold absolute pressure (MAP) sensor voltage and the barometric (BARO) sensor reading is not within range of where they should be.
Increased fuel consumption and loss of engine power with stalling and a rough running engine.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Ambient Air Temperature Sensor Circuit A)
...Read MoreIndicates that a fault has been detected with the outdoor ambient air temperature sensor circuit
Climate control may not work properly and the outside temperature readings may also be inaccurate.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Ambient Air Temperature Sensor Circuit A Range/Performance)
...Read MoreIndicates that a fault has been detected with the outdoor ambient air temperature sensor circuit
Climate control may not work properly and the outside temperature readings may also be inaccurate.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Ambient Air Temperature Sensor Circuit A Low)
...Read MoreIndicates that a fault has been detected with the outdoor ambient air temperature sensor circuit
Climate control may not work properly and the outside temperature readings may also be inaccurate.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Ambient Air Temperature Sensor Circuit A High)
...Read MoreIndicates that a fault has been detected with the outdoor ambient air temperature sensor circuit
Climate control may not work properly and the outside temperature readings may also be inaccurate.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Ambient Air Temperature Sensor Circuit A Intermittent/Erratic)
...Read MoreIndicates that a fault has been detected with the outdoor ambient air temperature sensor circuit
Climate control may not work properly and the outside temperature readings may also be inaccurate.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
This is a fault that normally is unlikely to cause any other mechanical problems but it can cause some damage in certain circumstances so it should not be ignored and it should be repaired as soon as possible.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit Low Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit High Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit Low Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit High Bank 1)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit Low Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Intake Valve Control Solenoid Circuit High Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit Low Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Exhaust Valve Control Solenoid Circuit High Bank 2)
...Read MoreIndicates that a fault has been detected with the valve control solenoid circuit
Poor acceleration and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Fuel Rail/System Pressure - Too Low Bank 1)
...Read MoreIt's an indication that the pressure of the fuel is below the specifications needed for satisfactory fuel delivery to the engine.
Because fuel is not being delivered at the required pressure the engine will be starved for fuel so it may run rough, misfire and a loss of engine power during acceleration
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Fuel Rail/System Pressure - Too High Bank 1)
...Read MoreIt's an indication that there is an excessive fuel pressure which is above the specifications needed for satisfactory fuel delivery to the engine.
A rich air fuel mixture will send black smoke from your tailpipe and your engine may misfires and be hard to start. It may also go into ""limp"" mode with a loss of engine power and engine stalling due to the excess fuel. Fuel economy will suffer and you oil may become contaminated with fuel.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less(Fuel Pressure Regulator A Performance)
...Read MoreThe fuel pressure sensor is reporting that the fuel rail pressures are out of the specified range.
Because fuel is being delivered at higher or lower levels of the required pressure the engine may run rough, misfire and have a loss of engine power and poor fuel economy.
A OBD-II Bi-Directional scanner is used for reading the codes, interacting with the various systems and testing those systems and individual components and then finally clearing the codes once you have fixed the problem. Basic scanners will allow you to read the codes and clear most of them. Bi-directional scanners do all that as well and allow you to dig deeper into the various systems and interact with the various sensors, actuators and computers to help you "nail down" the fault precisely.
It could be considered a minor or a major problem depending upon the root cause the fault. A minor easy to fix problems can become a larger more expensive problems if it's ignored long enough.
A warning fault light is just that, it's a warning that there is a problem and if you ignore the warning light long enough it can result in extra damage to the vehicle under certain conditions. A stop engine light is a warning that serious damage could now be occurring or that the vehicle is unsafe to drive. If the stop engine light comes on immediately pull over to a safe spot and shut off the engine and get help.
That's a "loaded" question that can not be easily answered because for any given fault there can be many different seemingly unrelated reasons for the fault and also so many different items that could potentially need replacing or repairing. A good bi-directional scanner will go a long way in helping you "nail down" the problem and will get you pointed in the right direction.
Go to a store that has a wide range of parts and tools that also has hassle free returns. For parts I can no longer afford to get my parts from the local (very expensive) dealership which will often need to have the part ordered in (takes about a week usually). To save money and time I have found it easier to get it from Amazon where the selection is better, it arrive quicker and its cheaper than the local suppliers.
...Read Less